zhoujie
fee2e96eaa
- 新增VSCode编辑器配置，启用保存时自动格式化 - 新增DMA2_Stream5和USART1中断处理函数，优化SPI传输性能 - 移除TIM1相关配置和性能监控模块，简化系统架构 - 优化GPIO配置，将ADC_SYNC和PA8引脚合并配置 - 简化系统监控模块，仅保留采样计数和数据溢出统计 - 优化SPI配置，使用16位数据宽度并提高DMA优先级 - 提高USART波特率（USART1:2Mbps, USART3:921600bps） - 优化LTC2508驱动，增加初始化状态检查和缓冲区大小 - 修正数据存储模块，使用校正数据包而非校正结果结构体 - 优化RS485驱动，使用中断传输并添加传输完成回调 - 更新IOC配置文件，移除TIM1并调整中断优先级配置 - 新增系统监控简化说明文档，详细记录架构变更
95 lines
2.8 KiB
C
95 lines
2.8 KiB
C
/* USER CODE BEGIN Header */
|
|
/**
|
|
******************************************************************************
|
|
* @file gpio.c
|
|
* @brief This file provides code for the configuration
|
|
* of all used GPIO pins.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2026 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
/* USER CODE END Header */
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "gpio.h"
|
|
|
|
/* USER CODE BEGIN 0 */
|
|
|
|
/* USER CODE END 0 */
|
|
|
|
/*----------------------------------------------------------------------------*/
|
|
/* Configure GPIO */
|
|
/*----------------------------------------------------------------------------*/
|
|
/* USER CODE BEGIN 1 */
|
|
|
|
/* USER CODE END 1 */
|
|
|
|
/** Configure pins as
|
|
* Analog
|
|
* Input
|
|
* Output
|
|
* EVENT_OUT
|
|
* EXTI
|
|
*/
|
|
void MX_GPIO_Init(void)
|
|
{
|
|
|
|
GPIO_InitTypeDef GPIO_InitStruct = {0};
|
|
|
|
/* GPIO Ports Clock Enable */
|
|
__HAL_RCC_GPIOH_CLK_ENABLE();
|
|
__HAL_RCC_GPIOC_CLK_ENABLE();
|
|
__HAL_RCC_GPIOA_CLK_ENABLE();
|
|
__HAL_RCC_GPIOB_CLK_ENABLE();
|
|
__HAL_RCC_GPIOD_CLK_ENABLE();
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(GPIOA, ADC_SYNC_Pin|GPIO_PIN_8, GPIO_PIN_RESET);
|
|
|
|
/*Configure GPIO pin Output Level */
|
|
HAL_GPIO_WritePin(RS485_CTL_GPIO_Port, RS485_CTL_Pin, GPIO_PIN_RESET);
|
|
|
|
/*Configure GPIO pin : PC3 */
|
|
GPIO_InitStruct.Pin = GPIO_PIN_3;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
|
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
|
|
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : ADC_DRY_Pin */
|
|
GPIO_InitStruct.Pin = ADC_DRY_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
HAL_GPIO_Init(ADC_DRY_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pins : ADC_SYNC_Pin PA8 */
|
|
GPIO_InitStruct.Pin = ADC_SYNC_Pin|GPIO_PIN_8;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
|
|
|
/*Configure GPIO pin : RS485_CTL_Pin */
|
|
GPIO_InitStruct.Pin = RS485_CTL_Pin;
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
|
HAL_GPIO_Init(RS485_CTL_GPIO_Port, &GPIO_InitStruct);
|
|
|
|
/* EXTI interrupt init*/
|
|
HAL_NVIC_SetPriority(EXTI1_IRQn, 0, 0);
|
|
HAL_NVIC_EnableIRQ(EXTI1_IRQn);
|
|
|
|
}
|
|
|
|
/* USER CODE BEGIN 2 */
|
|
|
|
/* USER CODE END 2 */
|